Key Systems in Ready Mix Concrete Plant Process

ready mix concrete plant project

Ready mix concrete plants or RMC plants refer to a set of equipment that prepares concrete by using storage, feeding, batching, mixing, and control devices for various raw materials needed. This equipment mixes various aggregates, binders, admixtures, additives, and water in a certain ratio through a mixer, using centralized mixing to supply fresh concrete.

Concrete is an indispensable building material in urban development and construction. As urbanization continues to develop, the demand for concrete continues to increase, leading to the establishment of more and more ready mix concrete plants. AGICO CEMENT has many years of experience in constructing concrete batching plants. The company continuously accumulates technology, learns from experience, and optimizes the structural design and process flow of its concrete batching plants and mobile concrete plants, providing clients with precise batching, fast mixing, stable output, energy-saving and environmentally friendly concrete batching solutions.

Single-Stage and Two-Stage RMC Plant Processes

Based on the batching process, RMC plants can be divided into two types: single-stage and two-stage batching plants.

A single-stage concrete batching plant is one where aggregates such as sand, gravel, and cement are lifted all at once to the storage hopper at the highest level. Precise batching and weighing are done at this stage, and then the materials are mixed into concrete, with all materials falling due to gravity. This creates a vertical production process. This type of concrete batching plant has high production efficiency, low power consumption, a high degree of mechanization and automation, a compact layout, and a small footprint. However, the equipment is relatively complex, and the initial infrastructure investment is large, making it suitable for large, permanent batching plants.

In contrast, a two-stage concrete batching plant involves lifting materials like sand, gravel, and cement in two stages. In the first stage, the materials are lifted to the storage hopper for batching and weighing. In the second stage, the materials are lifted again and discharged into the mixer. This type of batching plant has simpler equipment, lower investment costs, and quicker construction time. However, it has a lower degree of mechanization and automation, requires more space, and has higher power consumption, making it suitable for small to medium-sized batching plants.

AGICO CEMENT is capable of manufacturing both types of batching plants. We choose the optimal process based on the specific project requirements and customer needs, providing the most suitable concrete batching solutions.

Structure & Key Systems of a RMC Plant

A concrete batching plant is mainly composed of several parts, including the aggregate batching system, feeding system, storage system, mixing and discharging system, pneumatic system, and control system. Simply put, materials are weighed and proportioned by the concrete batching machine from the storage system and then transported by a conveyor belt into the concrete mixer (mixing system). Once all the materials have been weighed and sent into the mixer, the mixing process begins. After the mixing is complete, the concrete is discharged and transported by a concrete truck to the construction site for pouring. The discharge marks the completion of one cycle of concrete production. The entire process is controlled by computer intelligent systems, ensuring fully automated operation.

concrete batching plant process
Structure of a ready mix concrete plant

1. Aggregate Batching System

The batching system integrates the storage, metering, and output of aggregates such as sand and gravel. It generally consists of storage hoppers and metering hoppers.

Depending on the grading requirements of the concrete being produced, the storage hoppers can be configured with three, four, or five bins, with four bins being typical. This configuration can accommodate the storage of aggregates for various gradings. The capacity of the storage hoppers usually depends on the production capacity of the batching plant.

Aggregate metering can be categorized into two types by metering methods: independent metering and cumulative metering of sand and gravel. Independent metering involves setting a weighing hopper under each storage bin. After metering is completed, the pneumatic gate of the weighing hopper opens, and the aggregate falls onto the horizontal conveyor belt for transportation. Cumulative metering involves using baffles on the horizontal conveyor belt to form a metering trough. The aggregate falls into the metering trough, and the cumulative metering is completed along with the conveyor belt. Both metering methods use electronic weighing and their dynamic metering accuracy complies with standard specifications.

2. Aggregate Feeding System

The function of the aggregate feeding system is to transport the metered aggregates into the mixer. This is generally done using a conveyor belt or a bucket elevator. The type of conveyor belt is selected based on site conditions. Typically, a flat belt is used for an incline angle of ≤22°, a shallow V-patterned belt for an incline of 22° to 30°, and a corrugated sidewall belt for an incline of 30° to 60°. For angles greater than 60°, a bucket elevator can be chosen. The belt speed is generally selected at 1.6 m/s, 2.0 m/s, or 2.5 m/s. Common belt widths include 650 mm, 800 mm, 1000 mm, and 1200 mm. The maximum conveying capacity of the inclined conveyor belt should meet the actual output flow rate of the horizontal conveyor belt.

The design and selection range for the conveyor belt’s conveying capacity is extensive, allowing it to be compatible with mixers of various specifications. Additionally, the conveyor belt can be equipped with protective coverings, maintenance walkways, and, if necessary, fully enclosed housings.

3. Powder Storage System

Powdered raw materials such as cement, fly ash, and slag powder are stored in powder silos. Powder silos can be designed with capacities of 100 tons, 200 tons, 300 tons, or according to user requirements. The smaller the capacity of the powder silo, the higher the demands on the supply chain for continuous concrete production. The amount of powder silos is determined by the types of powders required for the concrete.

The powder silo consists of a silo body, dust inlet pipe, supporting frame, and ladder. The sidewall of the silo can be equipped with a level indicator, and the lower conical section is fitted with an arch-breaking device. Ladders are installed on both the inner and outer walls, and the silo top has a maintenance opening, safety door, and dust collector. The dust inlet pipe runs from the lower section straight to the upper part of the silo body. The powder is directly transported into the silo via a bulk cement tanker connected to the dust inlet pipe.

When bagged cement is used at the batching plant, auxiliary equipment, such as a pneumatic bagged cement conveying pump, can be selected to transport the cement into the silo’s storage body.

ready mix concrete plant and powder storage
Powder silos in an RMC plant

4. Powder Feeding System

The powder feeding system transports materials such as cement and fly ash into the corresponding powder weighing hopper. The transportation of powder must be done within a completely sealed chamber to prevent environmental pollution and protect the materials from moisture. The most widely used equipment for this purpose is the O-shaped cross-section screw conveyor. The casing of the screw conveyor is made from seamless steel pipes, with common specifications including φ219, φ273, and φ325. The inlet at the rear of the casing is connected to the powder silo butterfly valve via a universal joint, while the outlet at the front is flexibly connected to the powder-weighing hopper through a canvas bag. The installation angle is generally between 30° and 45°, and can be up to 60° if necessary. The length of the screw conveyor should not exceed 14 meters, but different total lengths can be achieved by replacing the intermediate sections. For longer conveying distances, a screw relay system can be used, where two feeding ports are set in succession.

5. Mixing and Discharging System

The mixing system is the core of the concrete batching plant, where the mixer blends the received materials into homogeneous concrete. Currently, the commonly used type is the forced mixer. In this mixer, the drum remains stationary while the mixing shaft rotates, and the mixing arms drive the blades to guide and mix the materials inside the drum forcibly. This type of mixer is highly effective, typically producing homogeneous concrete within 30 to 60 seconds. A longer mixing time may be required to prepare special or specialized concrete. Forced mixers excel in efficiency, functionality, quality, and energy consumption.

After the concrete is mixed, it can be stored temporarily in the mixer or the discharge hopper beneath the mixer. Once the open-door signal is received, the mixer door or discharge hopper door opens, completing the concrete discharge process.

concrete mixing machine for RMC plants
Concrete mixer

6. Pneumatic System

The pneumatic system includes compressors, air storage tanks, supply pipelines, air-water separators, oil mist separators, pressure regulators, and solenoid valves. It provides compressed air to actuate cylinders for opening and closing the mixer discharge door, storage silo bottom door, metering hopper bottom door or butterfly valve, and discharge hopper bottom door, as well as for arch-breaking devices in powder silos.

The technical specifications of the compressor, such as its discharge capacity, are selected based on the specifications and quantity of cylinders and other actuators. Common specifications are 0.9, 1.3, and 1.6 m³/min, with operating pressures typically set between 0.7 and 1 MPa. The pipelines supplying air to the cylinders should include air-water separators and oil mist separators. Pipelines supplying air to arch-breaking devices should have air-water separators and pressure regulators, but not oil mist separators. The pressure regulator is generally set to approximately 0.2 MPa.

7. Control System

All controls are located in the control room, which manages and monitors the entire concrete production process, including aggregate, powder, water, and admixture handling and discharge. The control room features a centralized control system centered around computer control, allowing for comprehensive control and management of the concrete production process from the control console.

Scroll to Top