Cyclone Preheater Immersion Tube And Its Features

cyclone preheater dip tube

A cyclone preheater is a core piece of equipment in the new dry-process cement production technology. Located ahead of the rotary kiln, it utilizes the high-temperature, rolling-up gases accumulated inside the kiln. By employing a multi-stage circulating suspension preheating method, it allows for thorough heat exchange between the raw meal powder and the hot gases, completing both suspension preheating and partial raw meal decomposition in preparation for calcination in the kiln.

In the cyclone waste heat exchanger, the immersion tube (also called dip tube) of the cyclone preheater significantly impacts the separation efficiency of the powder-laden gas. The preheater dip tube, positioned at the outlet of the cyclone chamber, is one of the three primary sections where gas flow pressure drop occurs. The operating environment is extremely harsh — the gas rotates downward after passing through the volute and the straight section, ultimately forming a strong central rotating flow (known as the internal swirling volute) at the lower part of the dip tube. This flow interacts with the gas rotating along the tube wall, creating intense friction that generates turbulence. The dip tube is located in the convergence zone of these friction-induced flows and thus faces extremely severe conditions, especially in the C4 and C5 sections. Here, the dip tube is rapidly eroded by high-temperature, high-pressure, high-speed gas carrying powder particles, leading to swift damage and potential scrapping. Over the years, it has consistently been the weak link in the cyclone chamber. Therefore, the dip tube must be not only wear-resistant and capable of withstanding high temperatures, but also reliable, long-lived, and easy to install and maintain. In earlier designs, the dip tube was usually round and manufactured as an integral unit by rolling heat-resistant steel plates. However, with continuous development, segmented composite dip tubes are now widely used, consisting of soft-jointed hanging plates made from heat-resistant steel or high-temperature-resistant ceramic materials.

preheater dip tube hanging plates

Compared with the integral dip tube, the segmented dip tube offers numerous advantages, which will be discussed one by one in the following sections.

Long Service Life

Compared with the integral dip tube made of heat-resistant steel plates, the segmented dip tube fabricated from heat-resistant steel castings has distinct advantages. In environments with alternating hot and cold conditions, the integral steel plate dip tubes are prone to deformation, whereas the segmented steel casting dip tubes exhibit a strong resistance to deformation. Furthermore, heat-resistant steel castings offer superior abrasion resistance compared to steel plates. When the contents of Cr and Ni are similar, the steel castings also provide enhanced creep resistance and better high-temperature mechanical properties. For example, the maximum service temperature for 0Cr25Ni20 heat-resistant steel plates is 1035℃, while that for ZG40Cr25Ni20 heat-resistant cast steel reaches up to 1150℃.

Ease of Installation

Some cement manufacturers, when replacing the integral dip tube made of heat-resistant steel plates, have resorted to methods such as drilling openings in the straight walls of the cyclone chamber and using lifting equipment to insert the integral dip tube into the cyclone, or fabricating it in separate blocks and then welding it within the confined space of the cyclone. These approaches not only are labor-intensive but may also compromise the overall structure of the cyclone or make it difficult to ensure the welding quality of the dip tube.

The segmented dip tube overcomes many of the shortcomings associated with installing integral dip tubes. Its installation and maintenance do not require the removal of ancillary components, such as the air inlet duct, thereby reducing numerous disassembly and reassembly steps. Instead, the hanging plates are gradually moved into the manhole by hand, then suspended along the circumference of the dip tube on pre-installed latching devices. Each layer is offset and progressively hung until the required length is achieved. To prevent the hanging plates from swaying under the impact of high-speed gas flows, a positioning pin is installed beneath each plate to lock them securely in place, thus enhancing the overall performance. The entire installation process requires only 2 to 3 workers and takes 4 to 8 hours to complete. The segmented dip tube not only substantially reduces the installation workload and labor intensity but also minimizes maintenance efforts, simplifies management, and thereby improves the operational rate of the rotary kiln, saving significant expenses annually.

cyclone preheater suspension plates

High Adaptability

The segmented dip tube features excellent interchangeability among its hanging plates. Preheater dip tube hanging plates made by AGICO CEMENT are designed based on extensive past experience, incorporating advanced international technologies and practical expertise. Key considerations such as achieving a lightweight design, compact dimensions, ease of transportation, convenient access through the manhole, and seamless assembly have led to the development of mass-produced standard “plate samples” with a curved profile. As a result, regardless of variations in size, shape, or performance specifications among different dip tubes within a facility, multiple hanging plates can be connected to fully meet the design requirements.

The term “soft-linked” dip tube is used because the hanging plates are connected via movable joints rather than rigid joints. This design offers several advantages, including adjustable diameter, adjustable suspension support, and adjustable height. It is suitable for dip tubes of various shapes—such as circular, flat, or boot-shaped—and sizes, ensuring robust and reliable performance with excellent interchangeability. In practice, this adaptability allows for flexible repositioning: heavily worn hanging plates can be relocated to areas with lighter loads. Many manufacturers have reported significantly extended service lives after making such adjustments.

AGICO CEMENT’s cyclone dip tube offers superior service life, ease of installation, and high adaptability compared to traditional integral designs. Its innovative soft-linked design not only simplifies assembly and maintenance but also optimizes operational efficiency, reducing labor intensity and extending the service life of the preheater. Contact us today to learn more about our products and secure a competitive advantage for your production process.

Scroll to Top